|
|
Post by pt3r on Jan 15, 2023 11:35:42 GMT
Hello I am wondering whether the BUS CV on my cirrus module is not supposed to send out the midi note value? Because when checking on the meter module it seems like it is actually sending out the midi gate signal not the note cv value. The module wiki does not describe the bus cv connector but I was assuming a similar logic like with other modules with a bus cv connection.
|
|
|
|
Post by pt3r on Jan 15, 2023 12:32:58 GMT
All other modules seem to provice bus cv correctly except the noise module where the bus cv print is next to a connector that does not provice bus cv, the connector below does provide the bus cv signal but has no print next to it. robertlanger shall we call these faceplate bugs  |
|
|
|
Post by MikMo on Jan 16, 2023 13:44:43 GMT
Should modules put anything on the CV bus? It's in the Input section! I thought the CV bus was for the master module to put CV out for received MIDI notes, for modules to consume. Check it here: wiki.aemodular.com/pmwiki.php/AeManual/MASTER"The Master module also supplies the various bus CVs available on many modules, all are derived from the Midi information received. These bus CVs mean a lot less patch cables are needed in many cases." |
|
|
|
Post by pt3r on Jan 16, 2023 14:40:45 GMT
No the BUS connectors are output not input, they get fed by the midi connector on the mater module.
|
|
|
|
Post by MikMo on Jan 16, 2023 14:50:17 GMT
Yes that was i was trying to say.
I think i misread your initial post as your Cirrus module was not sending out CV.
But you meant (and wrote) the BUS CV was not sending the CV (converted from MIDI).
My bad.
|
|
|
|
Post by pt3r on Jan 16, 2023 15:01:28 GMT
Exactly instead it sends out the bus gate signal.
|
|
|
|
Post by pt3r on Jan 20, 2023 7:17:56 GMT
pol can you update the wiki pages for noise and cirrus?
|
|
pol
Wiki Editors
Posts: 1,349
|
Post by pol on Jan 20, 2023 15:42:40 GMT
pol can you update the wiki pages for noise and cirrus? I'll await reply from Robert re Cirrus as may be an issue and a CV is mean to be there....
The other I'll check my noise module for the "faceplate bug", and if the same suggest users try the next socket down fromn the text!
Pol.
|
|
|
|
Post by robertlanger on Jan 20, 2023 17:26:44 GMT
All other modules seem to provice bus cv correctly except the noise module where the bus cv print is next to a connector that does not provice bus cv, the connector below does provide the bus cv signal but has no print next to it. robertlanger shall we call these faceplate bugs Damned, yes!! The printing is wrong! BUS CV is the second socket from bottom, below is BUS CTRL. For over five years nobody has recognised it.... Yup, let's call it faceplate bugs  Should we open an extra thread for them?  ...and faceplatebugcorrectionstickers could be a new product!  |
|
|
|
Post by robertlanger on Jan 20, 2023 17:33:21 GMT
Hello I am wondering whether the BUS CV on my cirrus module is not supposed to send out the midi note value? Because when checking on the meter module it seems like it is actually sending out the midi gate signal not the note cv value. The module wiki does not describe the bus cv connector but I was assuming a similar logic like with other modules with a bus cv connection. I just checked the board; it should be correct. BUT: If the bus connector is plugged in shifted sideways (so only 5 pins are connected, then this behaviour would habben, because the gate pin is besides the CV pin on the bus. The power would be supplied nevertheless, because two pins are in parallel vor ground and +5V. |
|
|
|
Post by pt3r on Jan 21, 2023 11:28:47 GMT
Hello I am wondering whether the BUS CV on my cirrus module is not supposed to send out the midi note value? Because when checking on the meter module it seems like it is actually sending out the midi gate signal not the note cv value. The module wiki does not describe the bus cv connector but I was assuming a similar logic like with other modules with a bus cv connection. I just checked the board; it should be correct. BUT: If the bus connector is plugged in shifted sideways (so only 5 pins are connected, then this behaviour would habben, because the gate pin is besides the CV pin on the bus. The power would be supplied nevertheless, because two pins are in parallel vor ground and +5V. I opened up the rack and low and behold the power connector for cirrus was only plugged in with 5 pins. All is fixed now and cirrus sends out cv like a champ.
Thank you robertlanger. I never thought about opening up the modular to check the power connector. |
|
|
|
Post by pt3r on Jan 21, 2023 11:30:14 GMT
All other modules seem to provice bus cv correctly except the noise module where the bus cv print is next to a connector that does not provice bus cv, the connector below does provide the bus cv signal but has no print next to it. robertlanger shall we call these faceplate bugs Damned, yes!! The printing is wrong! BUS CV is the second socket from bottom, below is BUS CTRL. For over five years nobody has recognised it.... Yup, let's call it faceplate bugs Should we open an extra thread for them? ...and faceplatebugcorrectionstickers could be a new product! I guess this shows that how many users are patching midi signals on the modular? |
|
|
|
Post by robertlanger on Jan 22, 2023 7:59:27 GMT
Damned, yes!! The printing is wrong! BUS CV is the second socket from bottom, below is BUS CTRL. For over five years nobody has recognised it.... Yup, let's call it faceplate bugs Should we open an extra thread for them? ...and faceplatebugcorrectionstickers could be a new product! I guess this shows that how many users are patching midi signals on the modular? Oh yes, I'd really be interested to get an idea how many do this really. But, ofc, pitch controlling noise is not the most common case 😂 |
|
|
|
Post by pt3r on Jan 22, 2023 11:45:41 GMT
I guess this shows that how many users are patching midi signals on the modular? Oh yes, I'd really be interested to get an idea how many do this really. But, ofc, pitch controlling noise is not the most common case 😂 Challenge accepted 😂 |
|
Should we open an extra thread for them? 
